The air source heat pump type works by using a small amount of electricity to drive the compressor to run and put the whole heat pump system into operation.
Heat is continuously absorbed from the air through the evaporator.
Finally the heat absorbed and the heat generated by the electricity consumed is transferred to the water through the condenser.
This unit is determined by measuring the energy input (in this case, electricity) and the energy output (heat).
A heat pump with a CoP of 3 can produce 3 kW of heat from every 1 kW of electricity.
Modern heat pump systems can transfer three to four times more heat energy in the form of heat than they consume in electrical energy to do this job.
Other electric heating products such as the boiler, which has a COP = 1, mean that as much electricity as you want to produce heat is consumed.
So choose a product with a COP greater than 1 (JNOD's heat pump) and you'll save on your energy bills!
Furthermore, JNOD's heating and cooling heat pump has Inverter EVI technology, which will allow the heat pump to adjust its operating power according to the ambient temperature, which will be even better.
There are many different factors will influence on your heat pump's electricity consumption, for example lifestyle, size of heat pump, heating space size,etc.
Don't hesitate to contact JNOD for further advice and discussion on heat pump.
The heat pump water heater absorbs air energy through the compressor, releases heat through the refrigerant and then heats the hot water. In general, it is a purely electric or boiler fuel, and the air source is supposed to transfer the energy of the air to the water through a certain amount of electrical energy. It is cost effective and has low operating cost. That's the most important thing. heat pump water heaters are safer, more energy-saving, more environmentally friendly, safer and fashionable than ordinary water heaters.
What is the basic working principle of a heat pump water heater?
What are the advantages of heat pump water heater and solar water heater?
Heating and cooling heat pump can be connected to Wi-Fi?
Heat pump water heater mainly consists of compressor, heat exchanger, axial fan, water tank for heat preservation, water pump, liquid storage, filter, electronic expansion valve and electronic automatic control. After switching on the power supply, the axial fan starts running, the outside air flows through the evaporator for heat exchange, and the reduced temperature air is expelled from the system by the fan. A kind of low pressure working medium gas is compressed into high temperature and high pressure gas and fed to the capacitor. The water forcibly circulated by the water pump also passes through the condenser and is heated by the working medium and fed to the consumer for use. The working medium is cooled to a liquid and the liquid expands. After the valve is throttled and cooled, it flows back into the evaporator. This cycle works repeatedly, and the heat energy in the air is continuously "pumped" into the water, so that the water temperature in the water tank for heat preservation gradually rises and finally reaches about 55°C, which is just suitable for people to take a bath.
Both work with air and solar energy, two of nature's renewable energy sources. What's the difference between the two?
In all seasons, even in winter, the effect of solar water heaters is very clear with sufficient sunlight, as well as on long rainy, snow and cloudy days. Solar water heaters cannot reflect the heating effect. The heat pump water heater is not affected by weather and season. It can supply hot water to users at any time. To be clear: The air flow heater can have hot water where there is air!
Wifi Monoblock High performance heat pump for heating and cooling, we offer not only advanced energy efficient heat pumps with advanced inverter technology, but also a total solution for heating, cooling and hot water supply in private homes. It has the WiFi remote. The heating and cooling heat pump can be controlled via Wi-Fi, allowing users to operate their heat pumps anytime, anywhere.
Guangdong JNOD New Energy Technology Co., LTD. can manufacture standard products under customers' brand, modify the products to meet customers' personalized requirements, and cooperate with customers to design and manufacture completely new products.
Guangdong JNOD New Energy Technology Co., LTD. focusing on heat pump& electric boiler R&D, manufacturing and providing comprehensive energy-saving solutions.
JNOD has a complete heat pump industry chain, and its products involves Swimming Pool Heat Pump, House Heating & Cooling Heat Pump, Domestic Hot Water Heat Pump, Heat Pump Dehumidifier, Commercial & Industrial High Temperature Water Heating Solution, Industrial and Agricultural Heat Pump Dryer,etc.The ultra-low temperature EVI heat pump has been widely used, too.
JNOD insisted on developing with technology innovation, it possessed of several national famous technicians and had invented multiply product patents. The company has been strictly implement the ISO international quality management system, and the products are of reliable guaranteed quality.
We are committed to providing customers the best hot water & heating solutions with our heat pump products, focusing on the latest technologies, strive for outstanding quality in our products and customer service.
In recent years, the potential energy of the sports industry under the national fitness, and favorable policies such as swimming into the high school entrance examination sports, the constant temperature swimming pool was once in short supply, and the Swimming Pool Heat Pump was out of stock.
What is the first stage of the workflow of Swimming Pool Heat Pump?
What is the second stage of the workflow of Swimming Pool Heat Pump?
What should we pay attention to when using Swimming Pool Heat Pump?
In the first step, the indoor hot and humid air in the swimming pool first exchanges heat with the outdoor fresh air through the heat exchanger to become warm and humid air, and then the warm and humid air flows through the evaporator, the temperature drops, and the water vapor condenses into cold water droplets and is separated from the air. Make the air dry and realize the function of air dehumidification; at the same time, the heat energy (latent heat and sensible heat) is released in the process of air cooling, water vapor condensation and cooling are absorbed by the refrigerant.
In the second step, the heat energy absorbed by the refrigerant first (latent heat) heats the pool water through the heat exchanger to realize the pool water heating function: the residual heat (sensible heat) passes through the air condenser to heat the cooled indoor air to realize the air insulation function. In the severely cold winter, when the energy available for the heat pump to extract in the air is too small, and the heat energy recovered by the heat pump is not enough to meet the requirements of the indoor air temperature, the auxiliary air heater is added to supplement the heat energy required for the indoor hot air. The Swimming Pool Heat Pump only needs to provide its own operating power, that is, it runs continuously according to the above working procedures, and achieves a harmonious balance of the three functions of pool water heating, air conditioning and dehumidification with low energy consumption.
1. When maintaining and cleaning the Swimming Pool Heat Pump, make sure that the Swimming Pool Heat Pump is in a power-off state. In addition, when the heat pump is not in use: the power supply should also be cut off.
2. Do not use gasoline, Tianna water, volatile oil, solvents and other chemicals, or liquid pesticides on the Swimming Pool Heat Pump, otherwise it may cause parts to crack and deform.
3. The area around the Swimming Pool Heat Pump should be kept dry and well ventilated.
4. Regularly clean the air-side heat exchanger to maintain a good heat exchange effect. If the shutdown time is long, the water in the pipeline of the unit should be drained, the power supply should be cut off, and the protective cover should be put on. When it is necessary to use it again, the system must be thoroughly checked before turning it on.
After reading, do you have a deeper understanding of Swimming Pool Heat Pump? For further information, please contact Guangdong JNOD New Energy Technology Co., LTD. They will be very pleased to help you.
The heating and cooling heat pump is a device that transfers heat energy from a low-level heat source to a high-level heat source, and is also a new energy technology that has attracted a lot of attention worldwide. It differs from the well-known mechanical equipment, which can increase the potential energy"Pumps"; A heat pump usually first extracts inferior heat energy from natural air, water or earth, then performs work by electricity, and then provides people with available energy that can be used. of high quality thermal energy.
What is the working medium of the heating and cooling heat pump?
What role does the heating and cooling heat pump play?
What do you know about heating and cooling heat pumps?
The working medium of the heating and cooling heat pump used to be Freon, but since Freon adversely affects the Earth's atmospheric ozone to protect the Earth's ecological environment, in addition to improving the cooling coefficient of the heat pump and effective use, science is also committed to new technologies in various countries. With the development of quality, the working fluid was used as a replacement for Freon. However, the work equipment of most Chinese manufacturers today is still R22, and the era of using environmentally friendly work equipment R417A and 134A has not yet arrived. Some countries, such as Japan, have taken the lead in using CO2 as a working medium to avoid damaging the ozone layer. (Therefore, the copper pipes must be firmly connected during installation to prevent R22 from leaking.) In addition, the above R22, R417A, 134A and CO2 do not harm the human body. Even if there is a leak, all the equipment is still safe.
The low temperature heat sources normally used in heat pumps for heating and cooling are the media around us. Air, river water, seawater, municipal wastewater, surface water, groundwater, treated water, fire pits or working fluids, which are discharged from industrial production plants these working fluids often have similar temperatures to the surrounding medium. The operating principle of the heating and cooling heat pump is the same as that of the compression chiller. In order to fully exploit its efficiency, the small air conditioner is cooled with the same equipment in summer or heated in winter. When heating in winter, the evaporator and condenser in the air conditioning system are exchanged via a switching valve.
Heat pumps for heating and cooling are an intelligent, efficient and versatile solution for year-round heating, cooling and hot water supply solutions. In addition to their flexibility and wide application, they are energy efficient and environmentally friendly, with advanced EVI technology and green refrigerant R32/R410A. So you can enjoy a comfortable home and save energy at the same time.
JNOD insisted on developing with technological innovation, it had several nationally famous technicians and had invented several product patents. The company has strictly implemented the international ISO quality management system, and the products are of reliable guaranteed quality.
Winter has arrived, and people tend to use heat pumps as heating machines. If the heat pump unit can be installed reasonably, the service life and heating capacity of the heat pump will be improved. Let Jnod tell you how to install it, see below:
1. Unit installation location planning
1) The installation requirements of the heat pump main unit are similar to the installation requirements of the outdoor unit of the air conditioner. It can be installed on the roof, balcony, and ground. The air outlet should avoid the windward direction.
2) The distance between the main unit (wind from the side) and the surrounding walls or other obstructions should not be too small. There should be no obstructions within 1 meter of the air outlet, and ensure that the heat exhaustion and suction of the heat exchanger are not hindered.
3) There should be no obstructions within 1 meter of the air inlet of the main unit (top air outlet), and no obstructions within 2 meters of the air outlet to ensure that the heat exhaustion and suction of the heat exchanger of the main unit are not hindered.
When the unit is installed under the eaves or there are horizontal obstacles above the unit, the installation location of the unit must be in a well-ventilated place, otherwise it is easy to short-circuit the air flow, resulting in poor heat dissipation capacity of the unit.
2. Unit installation environment control
1) Try not to place it in direct sunlight.
2) Not on the window sill of the bedroom or near the bedroom.
3) There is enough distance between the air inlet and outlet to facilitate heat dissipation.
4) Places that can withstand more than 2-3 times the weight of the outdoor unit.
5) A place where there is no oily smoke or other corrosive gas.
6) A place that does not affect other factors or the environment.
The heat pump water heaterabsorbs the low-temperature heat in the air, vaporizes the cold medium, and then compresses it through the compressor to increase the temperature, and then converts it through the heat exchanger to heat the water, and the compressed high-temperature heat energy is used to heat the water temperature.
What is the difference between a heat pump water heater and an air conditioner?
What are the advantages of heat pump water heater and compared with gas water heater?
What are the advantages of heat pump water heater compared to electric water heater?
When a general air conditioner is refrigerating, it absorbs the heat in the room through the phase change of the refrigerant in the evaporator (liquid to gas), and then realizes cooling through the heat release of the outdoor condenser. His heat exchange equipment is mainly finned heat exchangers. The heat pump water heater converts the low-grade energy in the air into high-grade energy that we can use. The heat is obtained by absorbing heat from the air through the phase change (endothermic) of the refrigerant in the evaporator, and then releasing heat through the indoor condenser (or jacket heat exchanger). This is his heating state. Its cooling is the same as that of general air conditioners, except that the heat exchanger may be different. General air conditioners use ordinary finned heat exchangers.
Gas water heaters heat the water temperature by burning combustible gas, and at the same time, will produce greenhouse gases such as carbon dioxide. If the continuous large amount of carbon dioxide on the earth exists in the air for a long time, it will produce a greenhouse effect on the earth's environment! The heat pump water heater only heats the water temperature with the heat in the air, and will not emit any toxic and harmful gases. In the era of energy saving and emission reduction, it is a water heater that is truly energy-saving and environmentally friendly. Secondly, gas water heaters may leak gas and cause human carbon monoxide poisoning accidents. Therefore, the safety of empty heat pump water heater is better than that of gas water heater.
We can compare heat pump water heater with electric water heater. Electric water heaters are heated with electric heating rods. The heat pump water heater heats the water temperature by absorbing heat from the air. The heat generated by the heat pump water heater consumes 1 kWh of electricity equivalent to the heat generated by the electric water heater consuming 4 kWh of electricity. In terms of energy saving, heat pump water heaters are far more energy efficient than electric water heaters. Second, in terms of security. The heat pump water heater just transfers the heat after compression heating to the water tank for heating, so the water and electricity are completely isolated. The electric water heater electric heating rod is directly heated in the water. Therefore, leakage accidents are easy to occur!
Guangdong JNOD New Energy Technology Co., LTD. is committed to providing customers the best hot water & heating solutions with our heat pump products, focusing on the latest technologies, strive for outstanding quality in our products and customer service.
A heat pump is part of a heating and cooling system. Like an air conditioner, it can cool your home, but it’s also capable of providing heat. In cooler months, a heat pump pulls heat from the cold outdoor air and transfers it indoors, and in warmer months, it pulls heat out of indoor air to cool your home. They are powered by electricity and transfer heat using refrigerant to provide comfort all year round. Because they handle both cooling and heating, homeowners may not need to install separate systems to heat their homes. In colder climates, an electric heat strip can be added to the indoor fan coil for additional capabilities. Heat pumps do not burn fossil fuel like furnaces do, making them more environmentally friendly.
HOW A HEAT PUMP WORKS
One of the most important things to understand about heat pump operation and the process of transferring heat is that heat energy naturally wants to move to areas with lower temperatures and less pressure. Heat pumps rely on this physical property, putting heat in contact with cooler, lower pressure environments so that the heat can naturally transfer. This is how a heat pump works.
A Heat pump in heating mode operates just like cooling mode, except that the flow of refrigerant is reversed by the aptly named reversing valve. The flow reversal means that the heating source becomes the outside air (even when outdoor temperatures are low) and the heat energy is released inside the home. The outside coil now has the function of an evaporator, and the indoor coil now has the role of the condenser.
The physics of the process are the same. Heat energy is absorbed in the outdoor unit by cool liquid refrigerant, turning it into cold gas. Pressure is then applied to the cold gas, turning it to hot gas. The hot gas is cooled in the indoor unit by passing air, heating the air and condensing the the gas to warm liquid. The warm liquid is relieved of pressure as it enters the outdoor unit, turning it to cool liquid and renewing the cycle.
Now, more and more families are making the preparation for the Winter, Like installing the heat pump for house heating and hot water.
No hesitate to contact us for OEM/ODM cooperation and development.