Heating And Cooling Heat Pump Quote- China Factory Manufacturers Suppliers

Heating and Cooling Heat Pump installs a four-way reversing valve on the basis of ordinary air conditioners, and changes the operation of the valve, which can exchange the functions of the evaporator and the condenser of the original air conditioner, so as to change the function of cooling indoor air. Changed to the function of heating indoor air.

What are the structural advantages of the Heating and Cooling Heat Pump?

What is the user's experience with Heating and Cooling Heat Pump?

Why the use of Heating and Cooling Heat Pump can save resources?

What are the structural advantages of the Heating and Cooling Heat Pump?

The evaporator of the Heating and Cooling Heat Pump adopts the method of countercurrent heat exchange for heat exchange to enhance the heat exchange effect; moreover, the heat exchange method combining fins and tube bundles is used, and each row of heat exchange tubes is arranged in a cross. The method of turbulence increases the convective heat transfer coefficient on the exhaust side and enhances the heat transfer effect;

The refrigerant tube bundle of Heating and Cooling Heat Pump is made of red copper, and the fins are made of hydrophilic aluminum foil. The condensed water in the exhausted air drips on the surface of the heat exchanger to form a water film that is conducive to heat exchange, increasing the heat exchange coefficient and enhancing the heat exchange effect;

The Heating and Cooling Heat Pump has an advanced microcomputer control system, and adopts a special programmable controller PLC for imported air-conditioning equipment, which has the ability to resist electromagnetic interference, intelligent coupling between building load and unit heating; Display, fault alarm and diagnosis functions.

What is the user's experience with Heating and Cooling Heat Pump?

The Heating and Cooling Heat Pumpis also very comfortable, clean and safe. In the past, when burning coal, it was not only dirty, tiring and troublesome, but also the temperature was not high, usually 14-16 degrees, and you had to wear cotton-padded clothes at home. Now open to 18 degrees and wear a thin sweater. If the weather is cold, turn up the temperature. Anyway, the Heating and Cooling Heat Pump is also very convenient, and you can adjust the temperature by pressing a button.

Why the use of Heating and Cooling Heat Pump can save resources?

The Heating and Cooling Heat Pump unit has the dual functions of supplying cold water in summer and supplying hot water in winter. Using air as the heat source and cooling source can greatly save water and avoid the pollution of water quality. The air-cooled modular cold and hot water unit can be placed on the top floor of the building or on the outdoor platform to work, eliminating the need for a dedicated cold source machine room and boiler room.

JNOD focuses on heat pump& electric boiler R&D, manufactures and provides comprehensive energy-saving solutions. Our sales team have extensive experience of overseas markets. We provide sincere and professional services, including OEM/ODM/project services, technology support, market analysis, usage of design and composition of installation.

When the indoor swimming pool is used in winter, it is necessary to heat the pool water to make the water temperature reach 26-28 degrees, which requires a lot of thermal energy. Boilers, gas, and electricity are gradually eliminated due to their low thermal efficiency and environmental protection. More and more people will Option to use Swimming Pool Heat Pump. So in addition to environmental protection, what are the benefits of Swimming Pool Heat Pump?

Compared with traditional boilers, what are the advantages of Swimming Pool Heat Pump?

What advancements have the Swimming Pool Heat Pump made?

Why is the demand for Swimming Pool Heat Pump increasing?

Compared with traditional boilers, what are the advantages of Swimming Pool Heat Pump?

Compared with traditional boilers, Swimming Pool Heat Pump does not use any fuel such as coal, oil, gas, etc., and does not produce open flames and exhaust emissions. Therefore, the use of air source heat pumps not only protects the atmospheric environment, but also eliminates fire, explosion, poisoning, etc. Accident happens. Compared with ordinary electric water heaters, it consumes less power, avoids leakage accidents, saves energy and is environmentally friendly. Compared with solar water heaters, air energy heat pumps are not affected by weather, geography, climate and other factors when working Sunny can be used normally.

What advancements have the Swimming Pool Heat Pump made?

smart system

① The unit control system adopts intelligent control. When customers use it, they only need to set the air temperature, humidity, and pool water temperature, and then the equipment will enter the fully automatic operation state, and there is no need for special personnel to take care of it.

② Customers can learn air temperature, humidity and other data through the touch-type full-color screen. Real-time value of pool water temperature and operating status of equipment.

③ Customers can also choose a communication interface according to their needs to implement remote control, monitoring and connection with the system.

ventilation system

Customers can choose the intelligent ventilation system of Swimming Pool Heat Pump. After choosing this system, the unit will control the amount of fresh air entering the room according to the concentration of carbon dioxide in the room, which can greatly save the energy consumption during operation.

Why is the demand for Swimming Pool Heat Pump increasing?

Not only that, the advancement and development of sports equipment and facilities and equipment technology have also provided a foundation for more people to actively participate in fitness. Take swimming, the most popular sport, as an example. In the past, people swimming in open-air pools or public waters were easily limited by the temperature environment. If they accidentally caught a cold, it would be bad for their health, and microbial bacteria would grow in public waters. , the health situation is not optimistic. In recent years, with the advancement of Swimming Pool Heat Pump related supporting technical facilities, many swimming pools and other fitness places are equipped with heated swimming pools, and even schools, communities, villas, etc. are equipped with heated swimming pools, so that people can not only enjoy the hot summer. The fun of refreshing swimming can also have a comfortable swimming experience in the cold winter.

If you would like to receive more information about the Swimming Pool Heat Pump, please connect Guangdong JNOD New Energy Technology Co., LTD., and they will be happy to answer your question!

JNOD has a complete heat pump industry chain, and its products involves Swimming Pool Heat Pump, House Heating & Cooling Heat Pump, Domestic Hot Water Heat Pump, Heat Pump Dehumidifier, Commercial & Industrial High Temperature Water Heating Solution, Industrial and Agricultural Heat Pump Dryer,etc.The ultra-low temperature EVI heat pump has been widely used, too.

Interclima is coming~

Interclima is the living history of all stakeholders in the sector HVAC in building: manufacturers, distributors, installers, consultants and project managers, maintenance and operating companies, contractors … As part of the Mondial du Bâtiment, it also shines internationally. The technology and equipment of  renewable energy , the quality of indoor air  nd ventilation, heating and hot water.

The INTERCLIMA 2022 will take place on 4 days from Monday, 03. October to Thursday, 06. October in Paris. The JNOD team is exhibiting with our latest boiler, Heat pump products, booth number is Pav.3-E111, welcome to visit us to discover our new products.

· From Monday 3 to Thursday 6 October 2022

· Venue: Paris Porte de Versailles (VIPARIS)

· City: Paris

· Booth Number: Pav.3-E111

With the soaring price of gas and the emphasis on environmental protection in many countries around the world, heat pumps are becoming more and more important and popular among consumers and manufacturers. In the last 2 years, many various kinds of heat pumps have appeared on the market. In this article, we will teach you how to choose a good hybrid hot water heat pump, also called all in one heat pump water heater.

For a hot water heat pump, the water tank is very important, both the outcase and the interior are very important.

* Internal

At this point, we would recommend our customers to choose a hot water heat pump with an enameled water tank for the following reasons.

A. Good thermal insulation: Take JNOD's all in one heat pump with enameled tank as an example. After testing, when the water in the tank is boiled to the set temperature and then power off, the water in the tank will only have a temperature drop of 5-8 degrees Celsius after 24 hours. Such a hybrid heat pump is your wise choice.

B. Strong corrosion resistance: In areas with bad water quality, there are more impurities in the water. If you use the general iron water tank, the welding joints inside are prone to chemical reaction with impurities, which leads to the problem of water leakage.

* Outcase

Here we recommend that consumers choose galvanized steel plate as the shell material. There are businesses in the market will choose color plate. The service life of the color plate is very short, only 1-2 years. A long time inside the box exposed will also lead to water leakage problems in the tank.

Expect these suggestions will let you choose a better heat pump! Feel free to contact JNOD with any questions! Link:https://www.jnodheatpump.com

In recent years, the potential energy of the sports industry under the national fitness, and favorable policies such as swimming into the high school entrance examination sports, the constant temperature swimming pool was once in short supply, and the Swimming Pool Heat Pump was out of stock.

What is the first stage of the workflow of Swimming Pool Heat Pump?

What is the second stage of the workflow of Swimming Pool Heat Pump?

What should we pay attention to when using Swimming Pool Heat Pump?

What is the first stage of the workflow of Swimming Pool Heat Pump?

In the first step, the indoor hot and humid air in the swimming pool first exchanges heat with the outdoor fresh air through the heat exchanger to become warm and humid air, and then the warm and humid air flows through the evaporator, the temperature drops, and the water vapor condenses into cold water droplets and is separated from the air. Make the air dry and realize the function of air dehumidification; at the same time, the heat energy (latent heat and sensible heat) is released in the process of air cooling, water vapor condensation and cooling are absorbed by the refrigerant.

What is the second stage of the workflow of Swimming Pool Heat Pump?

In the second step, the heat energy absorbed by the refrigerant first (latent heat) heats the pool water through the heat exchanger to realize the pool water heating function: the residual heat (sensible heat) passes through the air condenser to heat the cooled indoor air to realize the air insulation function. In the severely cold winter, when the energy available for the heat pump to extract in the air is too small, and the heat energy recovered by the heat pump is not enough to meet the requirements of the indoor air temperature, the auxiliary air heater is added to supplement the heat energy required for the indoor hot air. The Swimming Pool Heat Pump only needs to provide its own operating power, that is, it runs continuously according to the above working procedures, and achieves a harmonious balance of the three functions of pool water heating, air conditioning and dehumidification with low energy consumption.

What should we pay attention to when using Swimming Pool Heat Pump?

1. When maintaining and cleaning the Swimming Pool Heat Pump, make sure that the Swimming Pool Heat Pump is in a power-off state. In addition, when the heat pump is not in use: the power supply should also be cut off.

2. Do not use gasoline, Tianna water, volatile oil, solvents and other chemicals, or liquid pesticides on the Swimming Pool Heat Pump, otherwise it may cause parts to crack and deform.

3. The area around the Swimming Pool Heat Pump should be kept dry and well ventilated.

4. Regularly clean the air-side heat exchanger to maintain a good heat exchange effect. If the shutdown time is long, the water in the pipeline of the unit should be drained, the power supply should be cut off, and the protective cover should be put on. When it is necessary to use it again, the system must be thoroughly checked before turning it on.

After reading, do you have a deeper understanding of Swimming Pool Heat Pump? For further information, please contact Guangdong JNOD New Energy Technology Co., LTD. They will be very pleased to help you.

The heating and cooling heat pump is a highly efficient, energy-saving device that makes full use of inferior thermal energy. Heat can be transferred spontaneously from a hot object to a cold object, but not spontaneously in the opposite direction.

How does the heating and cooling heat pump work?

What does the operating time of the heating and cooling heat pump have to do?

What is the function of the heating and cooling heat pump?

How does the heating and cooling heat pump work?

In the heating and cooling circuit of the heat pump, the heat Q0kcal/h is obtained from the low temperature heat source (outside air or circulating water whose temperature is higher than the evaporation temperature t0) and the mechanical work ALkcal/h is consumed, while the heat of Q0kcal/h is obtained from the low temperature heat source (outside air or circulating water whose temperature is higher than the evaporation temperature t0) and the mechanical work ALkcal/h is consumed. The heating system) provides the heat of Q1kcal/h, and the relationship between these heats corresponds to the first main law of thermodynamics, ie Q1=Q0+ALkcal/h

If the heating and cooling heat pump is not used and the heat is converted by mechanical work (or the high temperature heat source is heated directly by electrical energy, the heat obtained is ALkcal/h, and after the heat pump device is used, the high temperature heat source (heating system) receives more heat is obtained: Q1-AL=Q0, kcal/h This heat is obtained from a low temperature heat source, and this heat cannot be obtained without a heat pump device. Therefore, using a heat pump device can save fuel and use waste heat.

What does the operating time of the heating and cooling heat pump have to do?

The working cycle of a heating and cooling heat pump is exactly the opposite of that of a thermal engine. A thermal engine uses the energy of a high-temperature heat source to generate mechanical work, while a heat pump transfers heat from a low-temperature heat source to a high-temperature object by consuming mechanical work.

If the heat pump and the heat engine have two identical heat source temperatures, the thermal efficiency of the heat engine cycle is η=AL/Q1; the energy index of the thermal engine cycle – the heat conversion coefficient φ=Q1/AL, i.e. φ=1/η. The value of η is always less than 1, so the value of φ is greater than 1.

If the refrigerator and the heat pump have two identical heat source temperatures, the relationship between them is φ=Q1/AL=(Q0+AL)/AL=e+1, where η is the refrigerator's cooling coefficient. It can be seen that the minimum value of the heat transfer coefficient φ η1 and in this limit case Q0 E0, that is, no heat is absorbed from the low temperature heat source.

What is the function of the heating and cooling heat pump?

Green simultaneous universal heat pump for heating and cooling

We offer not only advanced, energy-efficient heat pumps with advanced inverter technology, but also a complete solution for heating, cooling and hot water supply of residential buildings.

WiFi remote control

The heating and cooling heat pump can be controlled via Wi-Fi, allowing users to operate their heat pumps anytime, anywhere.

Three in one function mode

Hot water (DHW) + Heating and cooling.

Guangdong JNOD New Energy Technology Co., LTD. Focus on research and development of heat pumps and electric boilers, manufacturing and providing comprehensive energy saving solutions.

Under normal circumstances, when the average temperature is -5°C, the Heating and Cooling Heat Pump can generate more than three times the amount of heat per kWh of electricity consumed, and the energy saving efficiency is as high as 75% compared to the direct conversion of electrical energy into heat; when the average temperature is - At 15°C, 1 kWh of electricity consumption can generate more than twice the heat; even at -25°C, the Heating and Cooling Heat Pump can normally provide heat for the room.

What are the similarities and differences between Heating and Cooling Heat Pump and solar water heaters?

What is PTC heating with Heating and Cooling Heat Pump?

What are the advantages of using the Heating and Cooling Heat Pump?

What are the similarities and differences between Heating and Cooling Heat Pump and solar water heaters?

From the scope of application, heating continuity, operating cost, and installation conditions, Heating and Cooling Heat Pumpis easier to popularize than solar heating equipment, and solar heating equipment will be more affected by environmental factors. At the same time, the thermal efficiency of Heating and Cooling Heat Pump is very high, consuming 1 kWh of electricity can get three heat energy, and even if the thermal efficiency of solar energy reaches 100%, consuming 1 kWh of electricity can only generate 1 heat energy. It can be seen that the public is most concerned about energy saving. When the environment is harsh in winter, the energy consumption of Heating and Cooling Heat Pump is lower than that of solar heating equipment.

What is PTC heating with Heating and Cooling Heat Pump?

PTC electric heater is a kind of heater with automatic temperature control and power saving. It uses PTC heat-sensitive ceramic element as heating source, corrugated sheet made of aluminum alloy as radiator, and the heater is composed of bonding and welding. . Electric vehicle air-conditioning heater PTC generally collects data from temperature sensors through the air-conditioning controller, and adjusts the output power to achieve temperature setting. Currently widely used in pure electric vehicles. However, when the Heating and Cooling Heat Pump is used for heating in winter, the power consumption of the battery is very large, which seriously affects the cruising range. Now they have turned their attention to the heat pump solution, or the parallel solution of the two.

What are the advantages of using the Heating and Cooling Heat Pump?

First, energy saving is beneficial to the comprehensive utilization of energy. Heating and Cooling Heat Pump absorbs the low temperature heat energy in the air, and converts it into high temperature heat energy after being compressed by the compressor, and its energy saving effect is quite significant;

Second, Heating and Cooling Heat Pump is conducive to environmental protection;

Third, the combination of cold and heat, the application rate of Heating and Cooling Heat Pump is high, saving investment,

Fourth, because the Heating and Cooling Heat Pump is electrically driven, it is more convenient to control.

The Heating and Cooling Heat Pump has achieved an irreplaceable position in furniture design. Guangdong JNOD New Energy Technology Co., LTD. is committed to providing various Heating and Cooling Heat Pumps of high quality for all customers from all over the world.

for multiple rooms. Mitsubishi Electric Wi-Fi Control is not limited to only managing one heat pump at a time. It truly is an intelligent multi tasker. With the purchase of additional interfaces, multiple indoor units can now be seamlessly …

Heat Pump Hot Water Heaters (12027 products available) 1 / 6 R410A WIFI Control Air To Water All In 1 Heat Pump Hot Water Heaters For Hotel House Domestic Hot Water

R410A Commercial High Temperature Heat Pump Contact Details Solareast Heat Pump Ltd. Contact Person: admin Tel: 8613727864674 Send your inquiry directly to us ( 0 / 3000) Other Products R410a Commercial Swimming Pool Heat Pump 50KW/170KW/220KW 25KW Commercial Swimming Pool Heat Pump Air Water Systems 120KG

2022-7-15 · Heat Pump Hot Water Heater - China Factory, Suppliers, Manufacturers. We've been committed to offering easy,time-saving and money-saving one-stop purchasing service of consumer for Heat Pump Hot Water Heater, Air Water Heatpump, Heat Pump Pool, Inverters Air/Water Heat Pump,Pump Heat Pump. Our aim is to help customers realize their goals.

2022-11-6 · Swimming Pool Heat Pump for Water Temperature 45 Deg C - China Swimming Pool Heat Pump and Heat Pump price Home Consumer Electronics Water Heater

i-ForceLine Neo can be used for swimming pool heating or cooling. It is available to work at the ambient temperature of -2 °C to 40°C. Smart App for Option i-ForceLine Neo supports PHNIX smart APP control connected via WIFI or 4G DTU. Users can control the unit easily at anywhere and anytime. Intelligent Defrosting

Swimming pool heat pump top vent T8 Specifications: Model RS-9WX RS-13WX RS-22WX RS-26WX Rated Input Power 1.8 KW 2.6 KW 4.3 KW 5.1 KW Rated Heating Capacity 9.0 KW 13.0 KW 22.0 KW 26.0 KW Heating ampere 8.2A ... Read More 2020-09-16 15:58:34 Water To Water Heat Pump Unit With Panasonic Compressor For Bathtube Contact Now

Swimming Pool Heat Pump Rs 2.10 Lakh / Piece (Approx) Input Power : 6 kW Brand Name : Eco Tech Capacity Range : 100,000 Ltrs Material : Mild Steel more... View Mobile Send Inquiry 4 Yrs EcoTech Solutions Ahmedabad, Gujarat Domestic Swimming Pool Heat Pump Rs 1.72 Lakh - Rs 3.50 Lakh / Piece MOQ : 2 Piece (s) Input (kw) : 1.95 to 3.6